INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece.

We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. Seats – Remove both seats starting with the passenger pillion, if applicable. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover.

Suzuki gs150r manual pdf Virtual DJ for Mac supports the following formats TEMP,,,. I ve had to Restart when apps such such as the Store. Related Book Epub Books Suzuki Gs150r Service Repair And User Owner Manuals Pdf: - Home - Gone From My Sight The Dying Experience - Gone With.

Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box.

On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place.

Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap.

Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first.

Remove the battery. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back.

The Big Bang Simon Singh Pdf Files. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector.

Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions.

Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs.